Select Page

Worm drive gearbox with motor
A robust worm-drive gearbox powered by an MM28 motor. Ideal applications where a simple to match, high worm motor Torque output is required. Great for student based projects which includes robots and buggies.
The unit has been designed so that the output shaft can be ‘clicked’ in and out for modification. E.g. reducing to size. The motor is snap fitted into its cradle to engage the gear and worm.
Details
1 – 6V DC
0.1A to 1A based on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + electric motor: 35(W) x 40(H) x 60(L)mm
The primary feature of this high-efficiency gear box is a worm gear, which locks the output shaft whenever the engine isn’t turning. The high equipment ratios of 216:1 or 336:1 make this gearbox appropriate for small strolling robots, lifting mechanisms, and additional applications where high torque can be desired.
The low-voltage motors in the worm gearbox operate on 1.5-4.5 volts and draw up to some amps, making them ideal candidates for the DRV8833 motor driver carrier. Electric motor overheating can be due to excessive stalling, even at very low voltages. We advise that you use stall-detection sensors, or simply view your robot, to make sure that it doesn’t stall for more than a few seconds at the same time.
This gearbox has a 4 mm diameter, round output shaft, which works with the wheels that are compatible with Tamiya 4 mm, round shafts. Our 3 mm universal mounting hub also matches on the smaller threaded end of the shaft, though it is not specifically designed to work with this type of shaft (the hub’s set screw could harm the thread on the shaft).
Ever-Power gear motors are economical, right-angle, worm-geared motors that install easily in the tightest applications. Economical right angle worm geared motors arranged new requirements for reliability, effectiveness and economic climate with unparalleled features including hollow shafts in the smallest sizes. An inverter friendly design offers easy integration at this point and a really future proof remedy. The Ever-Power gear engine offers total flexibility in mounting options includes shaft, base, encounter, and flange solutions. The electric motor terminal box could be mounted in alternative positions rotated in 90º steps around the motor frame providing for unparalleled integration possibilities.
Ever-Power gear motors comply with UNITED STATES and International criteria, including NEMA, IEC, CSA, and CE, the Ever-Power series allows for worldwide acceptance, a true total alternative for our global clients.
Superior protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dust tight and hose proof,and can be utilized outdoors or in wet and dusty conditions without the use of additional enclosures. Complete rated output is available at the result shaft of the unit.
Product Features
Power rating up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Completely enclosed, sealed against dust and water spray
Lubrication change first after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Standard), IP66 (Optional)
Additional features:
Connecting with Plug connectors.
With integrated inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to Sobre 60034
Corrosion category predicated on DIN ISO 12944-5
C1, C2, C3, C4, C5-I, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm equipment motors are the alternative for applications requiring a corner turn, optional dual result, or an inability for the engine to be back again driven. The DC right angle gear motors are designed for continuous and intermittent duty procedure. Our right angle gear reducers are designed with many mounting plate options, making them perfect for a number of DC engine based applications. You can expect 12 ratios ranging from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Standard brush life of 2000+ hours (varies by application)
EP Products Worm Equipment Motors are created to generate high torque in a little package size. Worm Gear Motors are excellent for applications that want a personal- locking or breaking feature since the result shaft can’t rotate when there’s no power used. Additionally, Worm Gearheads can transfer motion in 90 degrees. With various decrease ratios, precision cut gears, voltages and sizes, EP Products has a DC Worm Gear Motor solution for your application.
Features and Benefits
Very High Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Ability to Handle Large Gear Reduction Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Security Door Locks / Industrial Conveying Systems / Security Gates / Teeth Chairs / Ambulance Cots & Stretchers Many of our DC Motors can be complimented with one of our Worm Gearheads. EP Products will work with you to create and manufacture a Worm Gear Electric motor that may optimize the efficiency of your specific application.
Built to your unique requirements
Engine Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Cut / Round / Splined / Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Extra Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm electric motor uses a metal gear box for sturdiness and a high torque output. Because of the special mechanical structure of the worm drive the electric motor output shaft is self locking and may not be rotated.
This part uses a two wire connection and supports direction control and also PWM speed control. Rated voltage is 12v and will attain 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Rated Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear devices from EP DRIVESYSTEMS especially show their power in applications where high equipment ratios are necessary. Our worm geared motors are consequently optimally suited for make use of in intralogistics, packaging technology and the food & beverage industry.
Four great known reasons for EP worm geared motors:
Rugged
Our worm geared motors have a high overload capacity
Maintenance Friendly
Washdown versions enable simple and effective cleaning of the drive program.
Corrosion protection
The NSD tupH sealed surface area conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular design give users maximum freedom.
The modular system for optimum flexibility: Our EP worm gear units
There are numerous applications that require drive systems, and each one of these has its own unique requirements. The EP series worm gear motors could be quickly and effectively adapted to satisfy your needs.
Worm gear products impress with their high power density and small style. If required, we can also supply them with the highly effective nsd tupH surface area treatment.
In addition to the basic EP housing, we offer an extensive type of bolt-on elements to customize the merchandise including torque arms, shaft covers and output flanges. These could be easily field installed, but we will also be happy to assemble the average person components for you.
Discover more about our modular SI worm geared motors!
Find out more
Soft and Clean: The EP worm equipment unit SMI
SMI worm gear systems feature a smooth, corrosion-resistant alluminum alloy casing. Optional nsd tupH surface area conversion makes the product ideally suited for harsh and challenging industries like food processing and pharmaceuticals.
Flexible input designs such as for example NEMA, IEC or direct motor mounts in extra foot or flange mounted housing designs.
Worm geared motors
Worm geared motors for little power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared motor program. The units possess on all sides different repairing possibilities and enable a simple assembling for the client.
Various other drive configurationscan be designed by use of built-on components (e.g. torque arm and output flanges). The housings are made in light weight construction out of aluminium die cast. Motor attachment is realised generally through IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:output shaft, output shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/mounting:uniblock, flange, torque arm
Purchase Worm Drive Gearbox with Engine – incorporating the following features: 1 to 6V voltage rating, 17100 rpm simply no load velocity, 220g-cm stall torque, 3mm shaft diameter, 60mm long, 35mm wide, 40mm high, a robust worm drive gearbox powered by an MM28 motor (included), most suitable for applications where an easy to match, high torque output is required, nylon housing and gear, requires light oil or silicon grease lubrication, perfect for student based tasks including robots and buggies.
Most ideal for applications where an easy to match, high torque result is required
Perfect for student based projects including robots and buggies
Reversible High torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Reversible High torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
Features:
The engine is Gear DC electric motor with micro-turbine worm, you can transform the wiring-connection to change motor rotation.
Turbo worm geared electric motor with self-lock, that’s, in the case of motor without electrical, the output axis is certainly fixed, self-lock.
The reducer output shaft arranged vertically with the motor shaft, whole motor output shaft relatively-short than general gear electric motor, widely used to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Result torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the windowpane, door, Mini winch. Ect.
In sumo robot or combat robot competition where high holding torque’s motor is essential to avoid your robot being pushed by your opponent robot. The worm equipment is definitely a better option compared to the spur gear motor. Why is worm gear so unique? Take a look wiki out: Worm Drive.
“Unlike with ordinary gear trains, the path of transmission (input shaft vs result shaft) is not reversible when working with large reduction ratios, due to the greater friction involved between the worm and worm-wheel, when usually a single start (1 spiral) worm can be used. This is often a advantage when it is desired to eliminate any probability of the result driving the input.”
In other phrases, it is tough to push your load (example, your robot) if the motor is not power or rotate.
Features and Spec:
Metal gear box
Output shaft is self-locking due to the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g