Select Page

Tractor PTO Gearbox Speed Increaser

Tractor PTO gearbox speed increasers are used for a variety of applications. For instance, the PTO speed increaser gearbox can be used for low and high-pressure water pumping. They can also be used for specialized farm equipment.

Tractor PTO Gearbox Speed Increaser

Tractor PTO gearbox speed increasers are used for a variety of applications. For instance, the PTO speed increaser gearbox can be used for low and high-pressure water pumping. They can also be used for specialized farm equipment.

A tractor PTO gearbox speed increaser is designed to change the PTO shaft output speed. It can be used as an increasing ratio gearbox. The PTO speed increasing ratio gearbox, on the other hand, increases the PTO shaft speed from 540 to 1000 rpm.

Tractor PTO gearboxes are made for connecting pumps and hydraulic systems to tractors. The proper running speed of the PTO is 540 rpm. This is comparable to the operating speed of hydraulic pumps. Different input running speeds are also suitable. A proper speed for the PTO gearbox is at least 3000 rpm. When the tractor is running at its highest operating speed, it will increase the pump speed by as much as three times.

Pto Speed Increaser Gearbox

PTO Gearbox Increaser

An auxiliary drive or PTO gearbox increaser adds additional torque to a drive line, increasing the output shaft speed by one or more ratios. This device can be either mechanical or hydraulic.

Mechanical PTO Gearbox Increaser

The mechanical PTO gearbox increaser allows you to change the PTO speed to optimize the performance of your implement. Typically, the PTO speed is increased while the wheel speed is reduced.

The main PTO specifications are defined by ISO 500-3. These specs determine the diameter of the shaft, its length and location. In some cases, a PTO will be intermittent. This is because the torque value is higher when the PTO is used for an intermittent operation. However, under continuous duty conditions, the torque can drop below 20%. It is important to check the gear oil in the mechanical PTO gearbox before use. It is recommended that the oil be replaced every 12 months or 1500 hours. Working temperatures should not exceed 120 degrees Celsius.

Hydraulic PTO Gearbox Increaser

A Hydraulic PTO Gearbox Increaser is a device used to boost the speed and torque of a PTO. An increaser can work in either direction, and the gearbox can be overdriven to double the output torque or reverse gearbox. Overdriven gearboxes are common in pump drives. A 3000 rpm hydraulic pump can't be fully utilized at a low 1000 rpm PTO speed. A speed-increasing gearbox mount can help in maximizing the efficiency of your hydraulic pump.

Another type of increaser is the through-shaft type, which allows for a hydraulic pump to be attached to the tractor. They also increase the output speed of the tractor PTO. The through-shaft type increases the PTO output speed by about three times, allowing the tractor to drive hydraulic pumps and other PTO attachments. A PTO gearbox should not be used with higher hydraulic power than the tractor's engine, and the hydraulic pump must have a 68-kW rating.

Intermittent PTO Gearbox Increaser

A good intermittent PTO gearbox increaser can add an extra 130mm to your drive line. It should apply a ratio of one and a half to one, and distributes the torque to either the output shaft or both. Some of these increases can be over 20%, and it is important to note that the torque values in these products are for continuous duty, while those for intermittent duty are de-rated by up to 30%.

A good way to find out the life of a gearbox is to test its efficiency. During the acceleration test, the gears make contact with a high load thirty times per second. When the gears were rotating at 1800 min-1, the tooth fitting had a higher failure rate than the bearings. This is why the gear fitting was adopted as the main failure mode. A gearbox that is more efficient in this way is more reliable.

WLY PTO Speed Increaser Gearbox

WLY PTO Speed Increaser Gearboxes are manufactured in several sizes. They are built to accommodate high-RPM components. Typically, these speed increasers incorporate tapered roller bearings and helical gears. Additionally, they can be customized with customer-specified shafts and connections. The tractor PTO gearbox speed increasers come with an aluminum housing and can increase either 540 or 1000 rpm. They can also be installed with an auxiliary hydraulic pump.

A hydraulic PTO pump is a high-performance gearbox speed increaser that can help boost the speed of your tractor PTO. It is typically large and powerful, and requires no special tools to install. They also require less power than electric motors and are particularly useful in applications requiring heavy loads, back-and-forth motion, and rugged conditions. If you need a tractor PTO gearbox speed increaser, consider purchasing a Speed "Step Up" Gearbox for your tractor.

Independent PTOs are also available. They feature a separate engagement clutch and engage independently of the transmission. A lever-operated clutch is necessary to engage the PTO before the separate PTO switch is engaged. The lever-operated version allows you to engage the PTO while the tractor is in motion. Hydraulic PTOs are a common choice for hydrostatic drive tractors. They are compatible with both mechanical and hydraulic transmissions.

PTO Shaft for PTO Speed Increaser Gearbox

Agricultural equipment such as tractors, combines, and harvesters use PTO shafts. These components are subjected to high loads and stress, and it is vital to find out why they failed in the first place. Constant compression of the shaft can damage connecting shafts and even the tractor and implement. A PTO shaft for an agricultural gearbox is an integral part of an agricultural implement or tractor. And PTO shaft for the agricultural PTO speed increaser gearbox is secured with a safety shield at both ends and can be found on implements and tractors.

A PTO drive shaft can be welded to the drive end by using a universal joint, while the rear shaft can be welded directly to the tractor.

Agricultural Gearbox and PTO Shaft

Additional information

Edited

Zqq

pruduct quality report

Materials Available

1. Stainless Steel: SS201, SS303, SS304, SS316, SS416, SS420
2. Steel:C45(K1045), C46(K1046),C20
3. Brass:C36000 ( C26800), C37700 ( HPb59), C38500( HPb58), C27200(CuZn37), C28000(CuZn40)
4. Bronze: C51000, C52100, C54400, etc
5. Iron: 1213, 12L14,1215
6. Aluminum: Al6061, Al6063
7.OEM according to your request
product materials available

Surface Treatment

Annealing, natural canonization, heat treatment, polishing, nickel plating, chrome plating, zinc plating,yellow passivization, gold passivization, satin, Black surface painted etc.

Processing Method

CNC machining, punch,turning, milling, drilling, grinding, broaching, welding and assembly
product finishing

QC & Certificate

Technicians self-check in production,final-check before package by professional Quality inspector
ISO9001:2008 , ISO14001:2001,ISO/TS 16949:2009

Eight reasons to choose us:

 

1. Perfect service system and after-sale protection.
2. Quality problems will be solved within 24hours.
3. One-to-one customer service tracking processing.
4. Companies carry out the ERP management, improve enterprise fast response.
5. Quality assurance, one year warranty.
6. Supporting professional matched other equipments.
7. The company has more than one product testing units, the implementation of ISO9001: 2015.
8. Unique development and design capabilities to meet the needs of special-purpose equipment manufacturing.

 

Five Core strengths:

 

1. The first domestic independent R & D manufacturer and 22 years of professional manufacturing.
2. Casting exquisite, beautiful, practical and durable.
3. Complete specifications, cost-effective and spot supply.
4. Independent research and development, special specifications can be customized.
5. Selected materials, high-tech treatment, up to the international standard test.

Package & Lead Time

Size: Drawings
Wooden Case/Container and pallet, or as per customized specifications.
15-25days samples. 30-45days offcial order
Port: Shanghai/Ningbo port

FAQ

Q: Are you trading company or manufacturer ?
A: Our group consists in 3 factories and 2 abroad sales corporations.

Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.

Q: How long is your delivery time ? What is your terms of payment ?
A: Generally it is 40-45 days. The time may vary depending on the product and the level of customization. For standard products, the payment is: 30% T/T in advance ,balance before shipment.

Q: What is the exact MOQ or price for your product ?
A: As an OEM company, we can provide and adapt our products to a wide range of needs.Thus, MOQ and price may greatly vary with size, material and further specifications; For instance, costly products or standard products will usually have a lower MOQ. Please contact us with all relevant details to get the most accurate quotation.