0 Items

PTO Shaft-Replacement of Walterscheid W2200 Series PTO Shaft

WLY Transmission can manufacture the replacement of the Walterscheid W2200 Series PTO Shaft, which is designed to provide reliable and efficient power transfer from the tractor to the attached implement. The W2200 Series PTO Shaft has a maximum torque rating of 3,980 Nm and a maximum speed rating of 1,000 RPM.

PTO Shaft-Replacement of Walterscheid W2200 Series PTO Shaft W2200 Series PTO Shaft

The W2200 Series PTO Shaft is a type of mechanical device used to transfer power from a tractor or other source of power to an attached implement, such as a mower or baler. It is designed to be used with agricultural equipment and is commonly found on tractors.

WLY Transmission can manufacture the replacement of the Walterscheid W2200 Series PTO Shaft, which is designed to provide reliable and efficient power transfer from the tractor to the attached implement. The W2200 Series PTO Shaft has a maximum torque rating of 3,980 Nm and a maximum speed rating of 1,000 RPM.

Some of the features of the W2200 Series PTO Shaft include a standard quick-release yoke, which allows for easy attachment and removal of the implement, and a telescoping design, which allows for easy adjustment of the length of the shaft to accommodate different implements. The W2200 Series PTO Shaft also includes a safety shield, which helps to prevent accidents and injury by enclosing the rotating shaft.

The W2200 Series PTO Shaft is a reliable and durable device that is designed to meet the needs of farmers and other agricultural workers. It is important to follow proper safety procedures when working with PTO shafts, including wearing appropriate protective gear and ensuring that the shaft is properly attached and secured before use.

W2200 Series PTO Shaft

W2200 Series PTO Shaft Specification

Application range
  • Small crop sprayers
  • Tedders
  • Windrowers
Properties
  • Tension side 1-3/8" (6) shaft collar kit
  • Machine side 1-3/8" (6) slide pin
  • Lubrication frequency from 50 to 100 hours
  • Fulfilling the requirements laid out in EC 89/392 EEC
  • Fulfilling the safety standard EN12965
  • CE marking available
Consists of
  • PTO shaft with shielding
  • Declaration of conformity
  • Instruction manual
Technical info
  • Max. dynamic capacity 540 rpm: 20 kW, 335 Nm
  • Max. dynamic capacity 1000 rpm: 31 kW, 295 Nm
  • Values at working angle 5° and service life 1000 hours
  • LZ = slid in length in mm, from intersection to intersection

W2200 Series PTO Shaft Parts

The W2200 Series PTO Shaft is a common driveline component used in many agricultural and industrial applications. Here are the parts found in a W2200 Series PTO Shaft.

Walterschied PTO Shaft Parts*Cross & Bearing Kit and Outboard Yokes interchange with Bondioli 2 Series

W2200 Series PTO Shaft Tractor Yoke

Dim. “A” Dim. “B”
mm
in.
Safety Slide Lock

Safety Slide Lock

1 3/8” x 6 Spl. 106.0 4.17”
1 3/8” x 21 Spl. 105.0 4.13”.
Quick Disconnect YokeQuick Disconnect Yoke 1 3/8” x 6 Spl 98.0 3.86”.
1 1/8” x 6 Spl. 94.0 3.70”
1 3/8” x 21 Spl. 98.0 3.86”

 

W2200 Series PTO Shaft Cross and Bearing Kit

Dim. “A”
mm
in. Dim. “B”
mm
in.
Cross and Bearing Kit 23.8 .94” 61.2 2.41”

 

Inner Profile Yoke of W2200 Series PTO Shaft

Dim. “A”
mm
in. Dim. “B”
mm
in.
Inner Profile Yoke

With Bearing Groove

34.5 1.36” 75.0 2.95”

 

Outer Profile Yoke of W2200 Series PTO Shaft

Dim. “A”
mm
in. Dim. “B”
mm
in.
Outer Profile Yoke

With Bearing Groove

41.3 1.63 75.0 2.95”

 

Inner Tube of W2200 Series PTO Shaft

Length
m
in.
Inner Tube of W2200 Series PTO Shaft 1.5 59.06”
1.0 39.37”

 

Roll Pin of W2200 Series PTO Shaft

Dim. “A”
Dim. “B”
mm in. mm in.
Roll Pin 10.0 .39” 60.0 2.36”

 

Outer Tube of W2200 Series PTO Shaft

Length
m
in.
Outer Tube 1.5 59.06”
1.0 39.37”

 

Implement Yoke of W2200 Series PTO Shaft

Dim. “A” Dim. “B” Standard Keyway
mm in. mm in. mm in.
Round Bore YokeRound Bore
With Keyway & Set Screw
25.0 .98” 80.0 3.15” 8.0 .31”
25.4 1.0” 80.0 3.15” 6.4 .25”
30.0 1.18” 80.0 3.15” 8.0 .31”
31.8 1.25” 80.0 3.15” 6.4 .25”
34.9 1.38” 80.0 3.15” 8.0 .31”
28.6 1.13” 80.0 3.15” 6.4 .25”
31.8 1.25” 80.0 3.15” 8.0 .31”
Dim. “A” Dim. “B”
Pinhole
mm in. mm in. mm in.
Shear PinShear Pin
With Pin Hole
31.8 1.25” 80.0 3.15” 6.35 .25”
35.0 1.38” 92.0 3.62” 12.9 .50”
25.0 .98” 80.0 3.15” 8.0 .315”
30.0 1.18” 80.0 3.15” 10.0 .394”

 

Maintenance of W2200 Series PTO Shaft

W2200 Series PTO Shaft Maintenance is a necessity if you use heavy equipment. You should always check your equipment for problems immediately, especially the PTO drive shaft. Heavy-duty equipment is subject to a lot of stress. If you notice a problem, stop the machine and check the condition of the PTO shaft. There are several ways to do this. The most common cause of PTO shaft failure is an improperly adjusted clutch. Another cause is improper work angles. A lack of lubrication can cause excessive wear on the shield bearings. Shield bearings should be lubricated every eight hours. This prevents premature wear and extends the life of the shaft.

In addition to regular inspections, PTO maintenance should be done on a regular basis. Some PTOs require a physical inspection every hundred hours, which is not too often. More severe-duty applications, however, require more frequent inspections. You can visually inspect the W2200 series PTO shaft by removing the inspection cover. To check for unusual wear patterns, check the gears and check bearings. Aside from visual checks, you should also listen for changes in the normal sounds during operation.

W2200 Series Pto Shaft Maintenance

W2200 Series PTO Shafts and Agricultural PTO Gearbox

The agricultural gearbox and PTO shaft are two components of a tractor that work together to transmit power. The PTO shaft rotates at 540 to 1,000 rpm. The agricultural gearbox and PTO shaft are connected by yokes at both ends. Depending on the application, they may have a higher or lower torque rating. As a professional agricultural machinery parts supplier, we also offer a wide range of agricultural tractor gearboxes for sale. Contact us now to get more info!

Agricultural Pto Gearbox

Additional information

Edited

Zqq

pruduct quality report

Materials Available

1. Stainless Steel: SS201, SS303, SS304, SS316, SS416, SS420
2. Steel:C45(K1045), C46(K1046),C20
3. Brass:C36000 ( C26800), C37700 ( HPb59), C38500( HPb58), C27200(CuZn37), C28000(CuZn40)
4. Bronze: C51000, C52100, C54400, etc
5. Iron: 1213, 12L14,1215
6. Aluminum: Al6061, Al6063
7.OEM according to your request
product materials available

Surface Treatment

Annealing, natural canonization, heat treatment, polishing, nickel plating, chrome plating, zinc plating,yellow passivization, gold passivization, satin, Black surface painted etc.

Processing Method

CNC machining, punch,turning, milling, drilling, grinding, broaching, welding and assembly
product finishing

QC & Certificate

Technicians self-check in production,final-check before package by professional Quality inspector
ISO9001:2008 , ISO14001:2001,ISO/TS 16949:2009

Eight reasons to choose us:

 

1. Perfect service system and after-sale protection.
2. Quality problems will be solved within 24hours.
3. One-to-one customer service tracking processing.
4. Companies carry out the ERP management, improve enterprise fast response.
5. Quality assurance, one year warranty.
6. Supporting professional matched other equipments.
7. The company has more than one product testing units, the implementation of ISO9001: 2015.
8. Unique development and design capabilities to meet the needs of special-purpose equipment manufacturing.

 

Five Core strengths:

 

1. The first domestic independent R & D manufacturer and 22 years of professional manufacturing.
2. Casting exquisite, beautiful, practical and durable.
3. Complete specifications, cost-effective and spot supply.
4. Independent research and development, special specifications can be customized.
5. Selected materials, high-tech treatment, up to the international standard test.

Package & Lead Time

Size: Drawings
Wooden Case/Container and pallet, or as per customized specifications.
15-25days samples. 30-45days offcial order
Port: Shanghai/Ningbo port

FAQ

Q: Are you trading company or manufacturer ?
A: Our group consists in 3 factories and 2 abroad sales corporations.

Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.

Q: How long is your delivery time ? What is your terms of payment ?
A: Generally it is 40-45 days. The time may vary depending on the product and the level of customization. For standard products, the payment is: 30% T/T in advance ,balance before shipment.

Q: What is the exact MOQ or price for your product ?
A: As an OEM company, we can provide and adapt our products to a wide range of needs.Thus, MOQ and price may greatly vary with size, material and further specifications; For instance, costly products or standard products will usually have a lower MOQ. Please contact us with all relevant details to get the most accurate quotation.