PTO Shaft for Finish Mower
- 1-3/8″ X 6 Spline Quick Disconnect Yokes on Both ends
- Comes with Safety Guards and Check Chains
PTO Shaft for Finish Mower
When you buy a finish mower, it is essential to find a quality PTO shaft. A well-fitting PTO shaft is critical for safety and performance. A properly-fitting PTO shaft should be at least 1/3 of its length inside the tubing when the machine is operating. To make the job easier, here are some tips for finding a high-quality finish mower drive shaft.
PTO Shaft Code Explanation
For example:
1: The Types of Tubes(e.g.: T; L; ST; G)
2: The Series of Cross Kits
3: The Code of Color (YB=Yellow+Black)
4: The Code of Safety Shield Structure
5: Connection Method: Pin Connected
6: The Tractor End Yokes
7: The Implement End Yokes
8: Minimum Overall Length
Specification of Finish Mower Drive Shaft
|
Model number
|
T8-1600 05B SB YBIIP
|
|
Function
|
Drive Shaft Parts & Power Transmission
|
|
Use
|
Kinds of Tractors & Farm Implements
|
|
Yoke Type
|
Double push pin, Bolt pins, Split pins, Push pin, Quick release, Ball attachment, Collar.....
|
|
Processing Of Yoke
|
Forging
|
|
Plastic Cover
|
YW; BW; YS; BS; Etc
|
|
Color
|
Green; Orange; Yellow; Black Ect.
|
|
Series
|
T1-T10; L1-L6;S6-S10;10HP-150HP with SA,RA,SB,SFF,WA,CV Etc
|
|
Tube Type
|
Lemon, Triangular, Star, Square, Hexangular, Spline, Special Ect
|
|
Processing Of Tube
|
Cold drawn
|
|
Spline Type
|
1 1/8" Z6;1 3/8" Z6; 1 3/8" Z21 ;1 3/4" Z20; 1 3/4" Z6; 8-38*32*6 8-42*36*7; 8-48*42*8;
|
|
Place of Origin
|
Zhejiang, China
|
Production of PTO Shaft for Finish Mower
- WLY, a member of Ever-power, has been specialized in designing, and manufacturing driveshafts, steering coupler shafts, and universal joints, which have exported to the USA, Europe, Australia, etc. for years.
- Application to all kinds of general mechanical situations.
- Our PTO shafts are of high intensity and rigidity.
- Heat resistant & Acid resistant.
- OEM orders are welcomed.
Finish Mower Driver Shaft on Agricultural Gearbox
The PTO shaft for finish mower is durable and robust. Besides finish mower PTO shaft, we also provide agricultural gearbox for the mower. Contact us now if you are interested!
Assemble the PTO Shaft for Finish Mower to the Gearbox
The following steps are how to connect the PTO shaft for finish mower to the gearbox. To do this, you must somehow access the U-joint hidden by the very extended shroud on the tool end of the PTO shaft.
Release the locking pin of the PTO Shaft |
|
 |
When looking at the pin along the shaft, it is obvious that there is a screwdriver slot in the pin. The holes where the pins are located are slight "D" shaped. So now that you've rotated the pin, hopefully in the right direction, you can slide a thin screwdriver into the slot "above" the pin and pry the pin back as it now slides easily through the "D" hole.
I show the pin removed so you can see it's the pin. All that is required is to retract the pins. Remember to push it back and turn the screwdriver 180 degrees to "lock" it when reassembling the shaft cone. This pin can easily fall out! With the "locking pin" retracted, you can now fully rotate the shaft cone so that the three slots line up with the white-collar piece protruding from the shaft. The PTO collar unlocked is now shown in the fully unlocked position with the white label aligned with the shaft taper slot. You must extend the PTO drive shaft so that there is room to slide the yellow collar along with the shaft cone down the shaft. Now on to the next mystery, reassembly |
Reassemble the shaft |
|
 |
To reassemble the shaft, I stood it upright, squeezed the collar into the shaft slot, and now I can slide the yellow shaft cone and collar back into place! This can be quite difficult in areas where you have to make the axis work almost horizontally. Obviously, you can also remove the shaft on the PTO end but that would add more work. |
Lock the PTO cone |
|
 |
With the shaft cone sliding back onto the shaft body, all I had to do was twist the shaft cone to lock it. Shaft PTO interlock, inspection port yellow PTO cone, and collar. It's an access port, but it's also an alignment aid. When you have rotated the shaft cone so that the two holes are perfectly aligned, you can slide the "locking pin" back into its locked position, don't forget to turn the "D" of the pin 180 degrees so the pin doesn't fall out. |
PTO shaft grease fittings |
|
 |
You can see the grease nipple on the yellow collar (right) in the photo above. You must periodically lubricate these joints on both ends of the shaft. Occasionally there will be a plastic mold flash that can block this nozzle opening. Now is the perfect time to clean it up and verify that the shaft is lubricated. Check the shaft "U" joint grease. There's always a chance they'll dry out the "U" joint. |
Edited by Zqq.
Materials Available
1. Stainless Steel: SS201, SS303, SS304, SS316, SS416, SS420
2. Steel:C45(K1045), C46(K1046),C20
3. Brass:C36000 ( C26800), C37700 ( HPb59), C38500( HPb58), C27200(CuZn37), C28000(CuZn40)
4. Bronze: C51000, C52100, C54400, etc
5. Iron: 1213, 12L14,1215
6. Aluminum: Al6061, Al6063
7.OEM according to your request
Surface Treatment
Annealing, natural canonization, heat treatment, polishing, nickel plating, chrome plating, zinc plating,yellow passivization, gold passivization, satin, Black surface painted etc.
Processing Method
CNC machining, punch,turning, milling, drilling, grinding, broaching, welding and assembly
QC & Certificate
Technicians self-check in production,final-check before package by professional Quality inspector
ISO9001:2008 , ISO14001:2001,ISO/TS 16949:2009
Package & Lead Time
Size: Drawings
Wooden Case/Container and pallet, or as per customized specifications.
15-25days samples. 30-45days offcial order
Port: Shanghai/Ningbo port
FAQ
Q: Are you trading company or manufacturer ?
A: Our group consists in 3 factories and 2 abroad sales corporations.
Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.
Q: How long is your delivery time ? What is your terms of payment ?
A: Generally it is 40-45 days. The time may vary depending on the product and the level of customization. For standard products, the payment is: 30% T/T in advance ,balance before shipment.
Q: What is the exact MOQ or price for your product ?
A: As an OEM company, we can provide and adapt our products to a wide range of needs.Thus, MOQ and price may greatly vary with size, material and further specifications; For instance, costly products or standard products will usually have a lower MOQ. Please contact us with all relevant details to get the most accurate quotation.