0 Items

NEMA ODP Single Phase Electric Induction Motor

ODP (Open Drip Proof): An open motor in which the ventilating openings are so constructed that drops of liquid or solid particles falling on it, at any angle not greater than 15 degrees for the vertical, cannot enter either directly or by striking and running along a surface of the motor and designed for reasonably dry, clean, and well ventilated (usually indoors) areas. Outdoor installations require the motor to be protected with a cover that does not restrict airflow to the motor. NEMA ODP series are single-phase rolled-steel motors with open drip proof, ac motors, and induction motors. The electrical motors are developed by ourselves independently, according to NEMA. The output-rated power and mounting dimensions of the electrical motor are perfect by NEMA. The NEMA ODP motors have reasonable structure, slight vibration, and low noise; they are made in china.

NEMA ODP Single Phase Electric Induction Motor

ODP (Open Drip Proof): An open motor in which the ventilating openings are so constructed that drops of liquid or solid particles falling on it, at any angle not greater than 15 degrees for the vertical, cannot enter either directly or by striking and running along a surface of the motor and designed for reasonably dry, clean, and well ventilated (usually indoors) areas. Outdoor installations require the motor to be protected with a cover that does not restrict airflow to the motor.

NEMA ODP series are single-phase rolled-steel motors with open drip proof, ac motors, and induction motors. The electrical motors are developed by ourselves independently, according to NEMA. The output-rated power and mounting dimensions of the electrical motor are perfect by NEMA. The NEMA ODP motors have reasonable structure, slight vibration, and low noise; they are made in china.

TEFC motors are generally more expensive. This is because they contain extra equipment — the fan — and they serve a specialized purpose. Also, TEFC motors have a thinner, larger casing to allow for better heat dissipation, which adds to the cost.

Technical Features Of NEMA ODP Single Phase Electric Induction Motor:

1. Service Factor 1.15
2. Continuous Duty 40ºC Ambient
3. ODP (Open Drip Proof)
4. Class F Insulation With Class B Temp Rise
5. NEMA Design L
6. High Starting Torque and Low Starting Current
7. Rolled Steel Construction
8. Ball Bearings
9. Capacity Start/ Capacitor Run (1/3 thru 10 HP)
10. Rigid Base

NEMA ODP Single Phase Electric Induction Motor Technical Data:

NEMA Frame Code HP Sync Speed (r.p.m) Fully Loaded Data Locked Rotor Current at 230V (A) Torque Dim “C” for Foot Mounted Dim “C” for C Type
Speed (r.p.m) Torque LB-FT Eff(%) Current at 230V (A) Locked Down LB-FT Break Down LB-FT
56 N 1/3HP 3600 3450 0.51 68 1.8 18 1.63 1.03-1.34 11.05 11.05
56 N 1/3HP 1800 1725 1.02 67 1.9 18 3.60 1.97-2.53 11.05 11.05
56 N 1/2HP 3600 3450 0.75 71 2.5 25 2.32 1.34-1.97 11.05 11.05
56 N 1/2HP 1800 1725 1.50 70 2.6 25 5.30 2.53-3.63 11.05 11.05
56 M 3/4HP 3600 3450 1.12 73 3.6 35 3.13 1.97-2.75 11.05 11.05
56 M 3/4HP 1800 1725 2.24 72 3.7 35 7.50 3.63-5.26 11.05 11.05
56H M 1HP 3600 3460 1.52 74 4.8 45 3.82 2.75-3.63 12.6 12.6
56H M 1HP 1800 1730 3.04 73 4.9 45 9.00 5.26-6.80 12.6 12.6
56H J 1.5HP 3600 3460 2.24 76 6.7 50 4.50 3.63-4.60 12.6 12.6
56H J 1.5HP 1800 1730 4.48 75 6.9 50 12.5 6.80-10.1 12.6 12.6
56H J 2HP 3600 3460 3.05 77 9.1 65 5.50 4.5-6.0 12.6 12.6
56H J 2HP 1800 1730 6.10 77 9.2 65 16.0 10.1-13.0 12.6 12.6
182T H 3HP 3600 3460 4.48 79 13.0 90 7.50 6.0-6.8 15.7 16.45
182T H 3HP 1800 1740 8.91 80 12.9 90 22.0 13.0-19.0 14.5 15.25
184T G 5HP 3600 3460 7.53 81 20.9 135 11.0 8.6-13.5 15.7 16.45
184T G 5HP 1800 1740 14.98 82 21.0 135 33.0 19.0-30.0 15.7 16.45
213T G 7.5HP 3600 3460 11.20 81 30.8 200 16.0 13.5-20 17.75 18.50
213T G 7.5HP 1800 1740 22.26 82 31.0 200 45.0 30.0-45.0 18.90 19.65
215T G 10HP 3600 3460 15.26 82 41.5 260 21.0 20-27 18.90 19.65
215T G 10HP 1800 1740 30.36 83 41.8 260 52.0 45.0-60.0 21.25 22.00

NEMA ODP Single Phase Electric Induction Motor Installation Dimension:

NEMA ODP Single Phase Electric Induction Motor Installation Dimension

Frame A B D H BA E 2F1 2F2 AA AB AC T O P N-W U S R ES
56 6.5 4.15 3.5 0.34 2.75 2.44 3.0 0.88 5.65 4.45 7.75 6.45 1.88 0.625 0.188 0.517 1.41
56H 6.00 Slot 5.0
182T 8.5 6.5 4.5 0.41 2.75 3.75 4.5 5.5 1.1 6.7 5.40 1.75 9.10 8.35 2.75 1.125 0.250 0.986 1.78
184T
213T 10.45 8.5 5.25 0.41 3.50 4.25 5.5 7.0 1.1 7.5 6.25 1.75 10.65 10.05 3.38 1.375 0.312 1.201 2.41
215T

Applications of NEMA ODP Single Phase Electric Induction Motor

1. Commercial Pumps
2. Swimming Pool Pumps
3. Fans
4. Conveyors
5. Air Conditioning Equipment A.K.A HVAC
6. Small Machine Tools
7. Blowers
8. Augers
9. Household Electric Appliances
10. Equipment Requiring Direct Drive
11. High Starting Torque

Differences Between NEMA and IEC Electric Motors

IEC motors are commonly made with either finned cast aluminum or iron frames, while NEMA motors are made with finned cast frames and rolled steel frame housings. There are only slight differences in frame sizes based on shaft height. The shaft diameters and lengths are different between NEMA and IEC, as are the mounting base dimensions and mounting hole spacing.

If a plant’s motor population is mixed between NEMA and IEC, care must be taken when someone is sent to regrease motors. A significant difference is that NEMA motors commonly use polyurea-based grease, whereas most IEC motors use lithium grease. These greases are not compatible and should not be mixed.

Typically, NEMA motors are made with a side-mounted conduit box (F1 position) with leads for connections. Most IEC motors have the conduit box at 12 o’clock (F3) with a terminal block for connections.

NEMA motors usually do not have a shaft seal except for some severe-duty designs, such as those made for IEEE-841 compliance, where a noncontact rotating shaft seal is used. In some custom designs, a lip seal may be used on the shaft to prevent the ingress of liquids. Many IEC motors are supplied with a standard lip seal.

NEMA motors often have a “weep hole” at the lowest point of each end plate to allow condensation to exit. On severe duty motors, this hole is changed to a breather drain. This practice is not standard on IEC motors.

Over the past few years, NEMA has adopted IEC standards as part of MG 1. The levels of ingress protection (IP) for motors and cooling (IC) are shown in the MG 1 standard. Recently, the vibration standards have been harmonized.

IEC Electric Motors
NEMA Electric Motors

Additional information

Editor

Yjx

pruduct quality report

Materials Available

1. Stainless Steel: SS201, SS303, SS304, SS316, SS416, SS420
2. Steel:C45(K1045), C46(K1046),C20
3. Brass:C36000 ( C26800), C37700 ( HPb59), C38500( HPb58), C27200(CuZn37), C28000(CuZn40)
4. Bronze: C51000, C52100, C54400, etc
5. Iron: 1213, 12L14,1215
6. Aluminum: Al6061, Al6063
7.OEM according to your request
product materials available

Surface Treatment

Annealing, natural canonization, heat treatment, polishing, nickel plating, chrome plating, zinc plating,yellow passivization, gold passivization, satin, Black surface painted etc.

Processing Method

CNC machining, punch,turning, milling, drilling, grinding, broaching, welding and assembly
product finishing

QC & Certificate

Technicians self-check in production,final-check before package by professional Quality inspector
ISO9001:2008 , ISO14001:2001,ISO/TS 16949:2009

Eight reasons to choose us:

 

1. Perfect service system and after-sale protection.
2. Quality problems will be solved within 24hours.
3. One-to-one customer service tracking processing.
4. Companies carry out the ERP management, improve enterprise fast response.
5. Quality assurance, one year warranty.
6. Supporting professional matched other equipments.
7. The company has more than one product testing units, the implementation of ISO9001: 2015.
8. Unique development and design capabilities to meet the needs of special-purpose equipment manufacturing.

 

Five Core strengths:

 

1. The first domestic independent R & D manufacturer and 22 years of professional manufacturing.
2. Casting exquisite, beautiful, practical and durable.
3. Complete specifications, cost-effective and spot supply.
4. Independent research and development, special specifications can be customized.
5. Selected materials, high-tech treatment, up to the international standard test.

Package & Lead Time

Size: Drawings
Wooden Case/Container and pallet, or as per customized specifications.
15-25days samples. 30-45days offcial order
Port: Shanghai/Ningbo port

FAQ

Q: Are you trading company or manufacturer ?
A: Our group consists in 3 factories and 2 abroad sales corporations.

Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.

Q: How long is your delivery time ? What is your terms of payment ?
A: Generally it is 40-45 days. The time may vary depending on the product and the level of customization. For standard products, the payment is: 30% T/T in advance ,balance before shipment.

Q: What is the exact MOQ or price for your product ?
A: As an OEM company, we can provide and adapt our products to a wide range of needs.Thus, MOQ and price may greatly vary with size, material and further specifications; For instance, costly products or standard products will usually have a lower MOQ. Please contact us with all relevant details to get the most accurate quotation.