Select Page

EP brand alternative gearbox for woods rotary gearbox

NEW 40 HP GEARBOX Easy Enter 1 3/eight twelve spline output Interchangable with marketplace well-known dimension i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Many A lot more

Features
(1) model new 45 horse electrical power shearpin gearbox. This gearbox fits a number of diverse tends to make of 4′,5′ and some 6′ rotary cutters. I market a great deal of these packing containers each and every year for numerous different purposes and have ALL Replacement Components for this box, but with any luck , you won’t have to fear about that.
Here are the specs on the box:
*forty five horse energy gearbox
*Common 1-three/8″ smooth input shaft(where the pto shaft hooks on). The pto shaft is held on by a one/two shearbolt.
*duration of the enter shaft out of the gearbox is three” lengthy
*bolt gap sample for mounting is on the corners, 4-3/4 centre of gap to centre of gap. It takes a five/8″ bolt.
*12 splined output shaft(in which the blade provider hooks up on the bottom)
*one-nine/16 outside the house measurement above the output shaft splines- from the foundation of the output cap to the finish of the splines is 2-three/4″ lengthy- total length of the output shaft is four-1/two” long.
*will take a one” threaded castle nut and a carter essential on the bottom of the output shaft to protected blade pan(NUT is included – – BLADE PAN IS NOT!!)
*total height of the box from the top of the mower deck to the top of the box is 9-one/2″
This is a fairly heavy merchandise (forty seven lbs.) so freight is not low-cost, but we do not make something off of freight, what ever ups fees us we charge you.
40 HP
one:1:forty seven Ratio
one-three/eight” Sleek Enter Shaft with Shear Pin Gap
one-1/two” twelve-Spline Ouput Shaft
Bolt Pattern: six-one/two” (4) five/8″ Holes, 5″ Center Gap Needed for Shaft Assembly
The Input and Output Shafts Are not able to be Purchased Serparately.
They are Offered as a package.
The package contains the adhering to components: input shaft, enter gear, output shaft, output equipment.
The Shaft Kit Can not Be Divided.

EP brand substitution gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Information
Is your mower leaking, creaking or normally performing incorrectly? You have come to the correct spot.

Study under for the most common issues with rotary cutter gearboxes and their options (from fast and filthy, to professional).

Leaking Base Seal:
If you have wrapped some baling or fencing wire close to your output shaft and blown the seal, the expert factor to do is to exchange the seal.
If your output seal is intact, and you are ready to get ID, OD and thickness measurements (in millimeters), most bearing properties can purchase you up a generic double-lip seal that will get you back up-and-running. If not, give us a call and we can assist you sort out what you need to have.
A dental pick is the best way to remove the aged seal before pressing in the new 1.
If you’re fortunate enough to have a gradual-leak, the fast and soiled method is to operate automotive-kind grease in the gearbox until the new seal arrives in. Be positive to verify and include grease more usually than you would with oil, as this is NOT a expert fix.

Damaged Output Shaft:
Uh oh. You hit anything that didn’t shift. The good information is that the output shaft on most gearboxes is pretty simple to replace. The poor news is… it truly is seldom an isolated failure.
The 1st issue to do is to just take apart your gearbox and assess the complete extent of the hurt. If it is actually just the output shaft, you need to be able to change it out, no difficulty. The output shafts start off at about $70 and go up in cost dependent on the size of the gearbox.
Even so, in most situations, the bearings ($20/ea), seals ($ten/ea) and equipment-established ($70) will also typically consider a beating. If you’re unlucky, the output cap ($eighty) will also suffer some damage.
In this situation, it is typically more affordable to change the gearbox. Assess the price of parts to the expense of an whole, new, warrantied gearbox. Occasionally, even pros have to know when to contact it a day.

I Want to Modify my Enter Shaft:
If you are exhausted of modifying shear pins or searching back and observing that your mower hasn’t been cutting, you could want to install a slip-clutch pto shaft (Indeed, we promote these way too).
This generally needs putting in a 540-type, six-spline input shaft ($eighty five) on your mower’s gearbox.
Lucky for you, we did a publish-up on our site. It’s known as “How to modify the input shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all seem kind-of equivalent more than-the-mobile phone. The best point to do is to disassemble your gearbox and take a look at the gears and bearings. The problem will usually existing alone in the way of damaged/lacking equipment tooth, toasted gears (like that picture on our residence page), or blown bearings.
If every thing appears standard, consider changing the equipment-mesh. This is done with the mylar “gaskets” that sit among the primary gearbox case and the enter/output caps. Consider adding or eliminating some of these spacers right up until your gears have roughly one/eight”-one/4″ of totally free enjoy. Professionals can purchase replacements ($one-2) in different thicknesses, but we suggest the rapid and dirty approach of chopping your possess out of a sheet of mylar.
Don’t fail to remember to re-seal the gearbox with RTV after you’ve got found the correct combination. Even although they are called “gaskets”, they won’t seal your gearbox on their own.

That’s all on Gearbox geared motors For Horticulture Drive Systems, curious about even more?